Conduce Chile
General => Ruedas => Mensaje iniciado por: isofit en Junio 14, 2015, 20:14:14 pm
-
Estimados foreros
Tengo un veracruz diesel y estaba fallando la bateria..la cambie y hay viene lo peor la saque x completa para instalar la nueva y mi sorpresa que empeso a sonar la bocina y el auto no parte..se habra bloqueado??? No se que hacer.
saludos
-
Hola...no tengo idea pero en el manual del mazda al menos salia el procedimiento para cambiar la bateria...creo que una vez lo hice sin leer y me quedo la caga
-
Si mi problema es que desconecte la bateria del auto y lo deje asi mientras fui a comprar la otra,a intalar la nueva empeso a sonar la bocina y no partio...averiguando me dice que puede ser el inmovilizador se activo pensando que se lo va a robar y que nunca desconecte una bateria sin dejar de pasar corriente.
-
Entonces habría que cambiar la batería con el vehículo con el motor andando?
-
Encontre en la red el manual del veracruz y salia q casi habia q reconfigurar todo...
-
Leíste el manual para desconectar la batería? Los hyundai diésel tienen su maña según recuerdo
-
Metodo correcto, manual de taller para Santa Fe diesel, que viene siendo lo mismo pero mas pequeño.
EE -24 ENGINE ELECTRICAL SYSTEM
BATTERY DIAGNOSTIC TEST
1. Make sure the ignition switch and all accessories are
in the OFF position.
2. Disconnect the battery cables (negative first).
3. Remove the battery from the vehicle.
CAUTION
Care should be taken in the event the battery case
is cracked or leaking, to protect your skin fromthe
electrolyte. Heavy rubber gloves (not the household
type) should be worn when removing the battery.
LBIF061A
4. Inspect the battery carrier for damage caused by the
loss of electrolyte. If acid damage is present, it will be
necessary to clean the area with a solution of clean
warm water and baking soda. Scrub the area with a
stiff brush and wipe off with a cloth moistened with
baking soda and water.
5. Clean the top of the battery with the same solution as
described in Step(3).
6. Inspect the battery case and cover for cracks. If
cracks are present, the battery must be replaced.
7. Clean the battery posts with a suitable battery post
tool.
8. Clean the inside surface of the terminal clamps with
a suitable battery cleaning tool. Replace damaged or
frayed cables and broken terminal clamps.
9. Install the battery in the vehicle.
10. Connect the cable terminals to the battery post, making
sure the tops of the terminals are flush with the
tops of the posts.
11. Tighten the terminal nuts securely.
-
solucionaste el problema?, saca la bateria y empieza de nuevo, si hubo algun daño ya esta hecho, algunas personas reportan daños en la ecu, pero es cuando instalan la bateria al reves, ¿o ya lo llevaste al concesionario?
-
Hoy voy a llegar a probar lo que tu dices ayer con el tema del partido llegue muy tarde y para despertar a los vecinos con el sonido de la bocina ufff.
-
No paso nada ..alguien sabe de scanner de hyundai??
-
Mala pata, mas que falla debe ser alguna maña para reiniciar el sistema, llama a Juan Monsalves al 56997956070, cuentale el problema, los pasos que seguiste, a ver si puede ir a tu casa si es que eres de Santiago, el tiene un electrico super bueno que se dedica a los diesel, son ex SK Bergue.
-
Será posible que la nueva batería esté sin carga?
-
Al final la vinieron a revisar ayer y eran varios fusibles quemados que seguro fue cuando hice puente conotro vehiculo..muchas gracias por su ayuda.
-
Llamaste a los de hyundai o los del seguro?